Estimated build time: 1 minute Estimated required disk space: 9 MB
The FHS recommends that we use /var/lib/hwclock as the location of the adjtime file, instead of the usual /etc. To make hwclock, which is part of the util-linux package, FHS-compliant, run the following.
cp hwclock/hwclock.c hwclock/hwclock.c.backup && sed 's%etc/adjtime%var/lib/hwclock/adjtime%' \ ���hwclock/hwclock.c > tmp~ && mv tmp~ hwclock/hwclock.c && mkdir -p /var/lib/hwclock
Install Util-Linux by running the following commands:
./configure && make HAVE_SLN=yes ADD_RAW=yes && make HAVE_SLN=yes ADD_RAW=yes install
HAVE_SLN=yes: We don't build this program because it already was installed by Glibc.
The Util-linux package contains the arch, dmesg, kill, more, mount, umount, agetty, blockdev, cfdisk, ctrlaltdel, elvtune, fdisk, fsck.minix, hwclock, kbdrate, losetup, mkfs, mkfs.bfs, mkfs.minix, mkswap, sfdisk, swapoff, swapon, cal, chkdupexe, col, colcrt, colrm, column, cytune, ddate, fdformat, getopt, hexdump, ipcrm, ipcs, logger, look, mcookie, namei, rename, renice, rev, script, setfdprm, setsid, setterm, ul, whereis, write, ramsize, rdev, readprofile, rootflags, swapdev, tunelp and vidmode programs.
arch prints the machine architecture.
dmesg is used to examine or control the kernel ring buffer (boot messages from the kernel).
kill sends a specified signal to the specified process.
more is a filter for paging through text one screen full at a time.
mount mounts a filesystem from a device to a directory (mount point).
umount unmounts a mounted filesystem.
agetty opens a tty port, prompts for a login name and invokes the /bin/login command.
blockdev allows to call block device ioctls from the command line
cfdisk is an libncurses based disk partition table manipulator.
ctrlaltdel sets the function of the CTRL+ALT+DEL key combination (hard or soft reset).
elvtune allows to tune the I/O elevator per block device queue basis.
fdisk is a disk partition table manipulator.
fsck.minix performs a consistency check for the Linux MINIX filesystem.
hwclock queries and sets the hardware clock (Also called the RTC or BIOS clock).
kbdrate resets the keyboard repeat rate and delay time.
losetup sets up and controls loop devices.
mkfs builds a Linux filesystem on a device, usually a harddisk partition.
mkfs.bfs creates a SCO bfs file system on a device, usually a harddisk partition.
mkfs.minix creates a Linux MINIX filesystem on a device, usually a harddisk partition.
mkswap sets up a Linux swap area on a device or in a file.
sfdisk is a disk partition table manipulator.
swapoff disables devices and files for paging and swapping.
swapon enables devices and files for paging and swapping.
cal displays a simple calender.
chkdupexe finds duplicate executables.
col filters reverse line feeds from input.
colcrt filters nroff output for CRT previewing.
colrm removes columns from a file.
column columnates lists.
cytune queries and modifies the interruption threshold for the Cyclades driver.
ddate converts Gregorian dates to Discordian dates.
fdformat low-level formats a floppy disk.
getops parses command options the same way as the getopt C command.
hexdump displays specified files, or standard input, in a user specified format (ascii, decimal, hexadecimal, octal).
ipcrm removes a specified resource.
ipcs provides information on IPC facilities.
logger makes entries in the system log.
look displays lines beginning with a given string.
mcookie generates magic cookies for xauth.
namei follows a pathname until a terminal point is found.
rename renames files.
renice alters priority of running processes.
rev reverses lines of a file.
script makes typescript of terminal session.
setfdprm sets user-provides floppy disk parameters.
setsid runs programs in a new session.
setterm sets terminal attributes.
ul reads a file and translates occurrences of underscores to the sequence which indicates underlining for the terminal in use.
whereis locates a binary, source and manual page for a command.
write sends a message to another user.
ramsize queries and sets RAM disk size.
rdev queries and sets image root device, swap device, RAM disk size, or video mode.
readprofile reads kernel profiling information.
rootflags queries and sets extra information used when mounting root.
swapdev queries and sets swap device.
tunelp sets various parameters for the LP device.
vidmode queries and sets the video mode.
Util-linux-2.11h needs the following to be installed:
sh from the bash package
as from the binutils package
ld from the binutils package
chgrp from the fileutils package
chmod from the fileutils package
cp from the fileutils package
install from the fileutils package
ln from the fileutils package
mkdir from the fileutils package
mv from the fileutils package
rm from the fileutils package
cc from the gcc package
cpp from the gcc package
rpcgen from the glibc package
grep from the grep package
make from the make package
sed from the sed package
unam from the sh-utils package
whoami from the sh-utils package
cat from the textutils package